Due to Shopify for sponsoring in the present day’s video! Begin your individual enterprise for $5 in the present day by visiting …
source
Due to Shopify for sponsoring in the present day’s video! Begin your individual enterprise for $5 in the present day by visiting …
source
Copyright © 2022 Car Fix Guru.
Car Fix Guru is not responsible for the content of external sites.
Copyright © 2022 Car Fix Guru.
Car Fix Guru is not responsible for the content of external sites.
BIG fan of Ms. A… I mean she knows her stuff. Also, the "Richard what'd you do?!" reference was perfect.
Sandro should be a full-time host. Dude is unfathomably funny.
drainage clip: I once found about 1" of standing water in the trunk area. I have no idea how it got there; sopped it up with towels, then had my mechanic check the drain plugs. Haven't seen any more water, and I have been in some serious rainstorms. I don't recall it being in the rain with the trunk open, but I can think of no other explanation.
Renting a tool for free isn't a thing you have to put down a hundred dollar deposit on the tool Incase you don't bring it back or it gets damaged
Angelina makes the noodle stiff
damn in 10 months ya'll have goten over 1mil subs,
Mechanic:" Hey, Ted! When you are done using the Cheetah to unclog the drain, could you run to Advanced Auto and bring me back some Blinker Fluid? This Lexus is a quart too low!"
The kid with the UTI shirt on😂
4:06 I …I work in the tire industry, and while I am not a mechanic or engineer, I at least understand the principal that this is…*nuts* Oh my gods.
The only reason I watch these videos is because I have Hots for Teacher.
wheel breng walk it out with a airhamer
This was a really fun and informative video to watch. Yes, some of them were obviously not recommended methods of repairs, but thanks. This was really enjoyable!
So you hire mechanics for the answers but a backwards mechanic for the booth🤣🤣🤣🤣🤣
Would be nice if they were already inviting Sandro at this time. I'd expect to hear him telling for most of these that he already did that shpeept
Second to last I don’t think anyone considered it was on a torque stick which would be completely compromised with that heat lol
Congratulations on 7mil👏👏👏👏👏
8:45 I use technique with dry ice for interference fits,legit
Jer and the girl look related
i use a cheetah once to unclog a stupid toilet
My dad modified a small harmonic balancer puller to do ball joint installations on our Polaris rzrs and it works. We use it a lot.
With the 5 minute crafts square wheel "repair" video, it definitely isn't the same wheel. If you notice the square one is rusty on the inside of the wheel very clearly on the opposite side, but the "fixed" wheel isn't rusty. FAKE… but given its 5 minute crafts…… what is real with that channel?????? ….. nothing is my verdict.
I'm gay I love men this is my fiance phone but still don't reply 😂
11:57 i had the same thing happen to me, i had my hand slide right to the pulley before i yanked it out, stupid mistake
Am I the only one who got an ad of the crew motor fest with one of them in it 😂
Just gonna say this the guy that used freon to sleeve an engine is looking at a $15,000 fine from the EPA. Very very illegal…
Heating bearing race off works every time. Falls off.
Ngl I would shave tires for a show car tire set
If your oil filter is on its side, all you have to do is rotate the whole car around until it points down.
That tire peel took five years off of my life.
Most steel grades contract or expand .001 inches for every 100 degrees I believe so the engine sleeve hack is legit
Facebook is where every moron and idiot lives. Tiktok is where the special verity go to spew their cringe. I don't use either.
9:44
you can see the thing bending on both sides when hes hammering it.
the structural integrity of that knuckle is gone, he f#&$ed it up.
I came across this video because I've just been binging on Donut 🍩 and the appreciation at the end is really genuine. One thing that can be said about the guys at Donut is they fill a void that has been left behind by Top Gear. Definitely not comparing them, but I guess you could say I'm New Old School where I grew up on F&F, car mags and Jeremy Clarkson and I'm really thankful these guys fill that void. I hope they take it as a serious compliment 😁
the tool at autozone isnt free
Honestly didn't know cars had drain holes you need to check. Nothing about that in the owners manual lol.
If the guy sleaveing the engine would have had a torch in that cylinder for a few minutes before this. Yes, that is perfectly legit, and it would have had a perfectly fine life. If he didn't have to heat it and expand the cylinder and then chill and contract the insert separately, there's no way it would last very long. They are basicely the same size at the same temp
I was covered in ant bites after using the cheetah to blow up an anthill
You can definitely resleeve and engine like that. If you throw a torch inside the block and get it nice and hot, then flash freeze of the sleeve Sub-Zero with a can of compressed air (the one for computers is also a refrigerant by the way), you can definitely do that and it is that easy. Notice he got a block of wood to hammer the last little bit in.
Once that metal equalizes in temperature you won't be able to get that out and there will definitely be a good interference fit..
…at least he didn't fill the body with ramen noodles like i saw on a porcelain sink fix video 😀
Quick insight , autozone does not rent for free you need a deposit you get it back but man if you are broke you can hardly leave money for a 300 dollar tool
I'v been a subscriber since the "mow pawah bhaybeh" days.. I'm happy for your guys's success.. keep doing what your doing!
Can you imagine being a police officer and then going to pit maneuver that last car
sandro?
God loves you guys!
Truck mechanic checking in, Hack #1 with the hubs…… Works a treat on trucks. Especially Super duties up here in the rust belt. The Chain trick to set the spring on the shoes also works a treat, Doesn't deserve a ticket for sure.
Another way to remove a stud is to take him on a date
No way with that wheel bearing, I’d just weld a bead inside of it and then drop it and they just fall out 🤙
I love watching your videos! Keep em coming yo 😊
The last clip gives new meaning to hitting a brick wall.
Could you guys not find a female mechanic? So you settled on a teacher?