On this video we’ll present you the very best automotive elevate at present in the marketplace that you may set up in your tiny area. Max Jax has put …
source
On this video we’ll present you the very best automotive elevate at present in the marketplace that you may set up in your tiny area. Max Jax has put …
source
Copyright © 2022 Car Fix Guru.
Car Fix Guru is not responsible for the content of external sites.
Copyright © 2022 Car Fix Guru.
Car Fix Guru is not responsible for the content of external sites.
Hello
thanks for the video
I am interested in this car lift because I have a small garage
what are the approximate dimensions of your garage please; height and width?
THANKS
not a fan of using a concrete anchor that is removable. Hope they don't get weak!!
you put that tank in a bad place, you don't have any room to work on the passenger side and you look like you are in a residential neighborhood, and you are going to do body work there and drive everyone crazy! your door opener is right in the way!
Safety shoes recommended on this installation.
seazor lifter car -remain on bottom
Can I get professional installation.?
Very smart working with heavy steel wearing sandals 😂
Man I would have lifted that last car to its max capability! I have full trust in bendpak! Been using them for years! Best in the business
STEP 1: Make sure you garage concrete slab is not post tensioned…
I couldn't finish watching this because of the massively irritating "music".
When do you plan to an update on the Max Jax and the concern you had of removal and replacement.
Portable is not bolted to the ground.
Too bad, you couldn't demo that lift in a proper garage to see how high goes. No way I could stand up and work under that car and your garage.
Idiot took the locks off and then went under the car😂😂😂😂
Isn't there a pod weight to keep the lift from tipping into the car. I've seen cement poured really heavy and deep to counter weight the weight of the car.
you fix the lift on the ground, how s the portable work, what s the meaning of protable
Great idea but I wish they offered a taller one that would lift up to 1.8-2m
That roller creeper chair seems like a PITA. The slightest force turning a bolt will send it rolling away.
Not enough hight, and useless if you can’t walk around the car, you don’t soon get feed up having to walk around the car from wheel to wheel, maybe ok for a midget to get underneath, 😂😂🤷♂️
Safety wise I would never have put the controls in such a tight spot. If this lift where to fail or the vehicle becomes unbalanced one could be pinned between the vehicle and the wall. This would likely prove to be fatal. Since you were running longer hose to one side anyway, I would have put the pump and controls on the rear wall where you could more easily escape if a car starts to fall. This would also give you more equal hose lengths. I have two four post lifts and the controls are at a corner where one can easily escape in case of failure. It is much more rare for a car to fall of a four post lift, but I have seen dozens of videos of cars falling off of two post lifts. If you watch those videos you would not ever think of being so trapped when lifting a vehicle.
definitely would've put it in the middle bay🤦♂️
Super portable just take the garage floor with you 😂
I guess I have a different definition of "portable". If I'm willing to unbolt and disconnect wiring then wouldn't everything be portable?
Very nice. I’d worry about the amount of leverage on those bolts. I’d prefer a wider foot print and/or the pillar extending to the ceiling to be secured into ceiling beams. Both of those of course effect portability but safety first. Ignoring that, if you want more lift height, look at 1) high lift conversion on that end door and 2) jack shaft door opener. You can get another foot or more of overhead range. As long as you don’t open the door, you don’t need the high lift door but your torsion bar at present likely doesn’t have the space for a jackshaft opener on either side. You’ll probably be ok for opener space after doing a high lift conversion.
I purchased the 7K and had to put in another 2k to make it work and be safe. Did 24 inch square base plates 5/8 . Then replaced the movable parts of the arms to extend them to actually work.
Is that unit made by bendpak.Looks like a great unit thanks for the vid
.
Just the wrong place to install the controls. Better if its in the front.
So the mechanics are dwarfs?
Ok. Good thing I seen this video, another words this setup is garbage cause you can't open the door more like the actual lifts at the shop.
Very cool for a home garage. Make sure to double check everything always and lock doors when not in use.
Do you have another garage with all your possessions in it?
you have no room on the right tho . whats the point