Reveals each step from begin to end of the auto physique restore course of that each dent, scratch or chip should undergo. Instruments …
source
Reveals each step from begin to end of the auto physique restore course of that each dent, scratch or chip should undergo. Instruments …
source
Copyright © 2022 Car Fix Guru.
Car Fix Guru is not responsible for the content of external sites.
Copyright © 2022 Car Fix Guru.
Car Fix Guru is not responsible for the content of external sites.
The wizard and all his tips and tricks. Thank You.
May I ask why you didn't use an epoxy primer or possibly a etching primer? I'm VERY new at this and from everything I'm reading, I should be using epoxy primer to lock everything down before continuing. Is that wrong?
Thanks for the lesson and for the good tips and info!👍 Thanks for the video
Great videos
Another Great video keep up the good work
Hey Jerry
Nice concise rundown Amigo.
FELIZ NAVIDAD
Great tutorial, now I need to learn to paint, mix, spray everything.
Great vid, can you show a repair on a high area that was dented from behind?
Great demo. Quick but alot of info. 👍👍👍
Hi Jerry, Thank you for the succinct review on the auto body repair process! More body work for me coming up in the new year. Merry Christmas and Happy New Year! Side Note. I tried my hand at doing a little Cerakote on a set of headers. Very high temp coating and 500 degree cure. Very cool stuff but boy does it stink! Respirator all the way!😷
Could you do the same type of video for what steps to take after a rust repair section has been welded in and ground down. I hear conflicting advice on how to Seal the weld etc. And what to paint over it with. Thankyou
thank you for this video. just what i wanted to see.
Very well done Jerry! Merry Christmas and Happy New Year to you and your family.
Thank you! I’m an apprentice here in Australia
A lot of work you guys have to go thru but it sure does look good when done.
Haven’t seen a siphon feed spray gun in a looong time.
I been Applying Jerry’s auto body into my auto body well basically getting rid of my auto body I have gotten super fast . Great teacher I called him the only man on YouTube that actually teaches Autobody thanks Jerry you have a merry Christmas and happy holidays and a happy new year
I like links added on the screen for your previous in depth videos of each step of repair
How do you know when to switch to a higher sand paper each time? Do you sand until the surface feels even with every grit?
Isn't 240 a bit coarse for your finishing sanding pass before applying paint? I would think you'd want to go up to at least 400 before laying down some paint? Can you enlighten?
Pulled the Binks off the shelf for this one!👍
You make body work look so easy and easy to follow instructions…Thank You
Oh man I've learned so much and it shows in the work!
Thank you a million times !
I've got that fiberglass kit car I'm doing that's really warped up.
Anyway, I did a "semi sorta final prime" on the left side I was getting the body lines corrected.
It's where the rear cab window wraps around to the door ,and the joint where the fender tops meet.
It came out so good ,I've got to go back to the other side because I did that before watching your vids and I can see it's not as good.
I'm doing a few sections like this while it is half built ,as the areas are gonna be difficult when it's assembled.
The right side is assembled, and I gotta go back now but I should be able to persevere and win.
I'm just trying to get it straight enough, prime it and assemble the car so I can drive it this summer.
Looking at all the bodywork it'll need ,if might be 2 seasons before I get into that.
It's taken me 3yrs to build this thing, and for now I'm ok it's not getting painted.
I noticed you didn't apply any epoxy sealer or etching, is that because of using 60 grit on the surface to allow the primer to grab onto? This is where I get confused because every other video says different. No one really explains it's. Thanks in advance
Don't we need to sand the spray primer before the paint?
Thanks for this video..👍
Just got back with some 40for my block 👍🏻👊🏻
Excellent video tutorial! Well Explained, well demonstrated, concise/to the point and no bull.. Exactly what you want to see in any good DIY guide video!
Cheers from London 👍🏴🇬🇧
You da Man !!!
Fantastic video
6:53 What is the spray boom paint for? Why do you prime it again after the spray boom pant? Also, do you need to use a sealer or is primer surfacer good enough on bare metal?
What's the cheapest compressor I can get away with for spaying surfacer/ paint?
Excellent, much needed for me.
What degreaser do I buy?
When it comes to masking do you recommend any particular brand of tape? In addition, what material do you prefer: plastic or paper? Please cite manufacturer. Thank you in advance.
Frank
Excellent video tutorial!
U know your trade ,best of luck!
you left out a ton of detail.
Very good. Straight to the point
This awesome. I just got vehicle and was sideswiped. I love the detail ty
Thank you. That's what I was looking for. Very good tools and simple steps